Brief:
This is a Quasar Patriot kit with 38mm motor mount instead o' 3 x 24mm, through t' wall Microlite fins instead o' surface mount balsa, lightweight tape-together clamshell electronics bay for dual deployment recovery, shortened nose cone shoulder, arrr, and deleted large metal eye bolt for weight savings. Ahoy! Positive motor retention added.

Modifications:
T' Quasar Patriot kit, motor, ya bilge rat, me hearties, and most o' t' modification materials were purchased at Apogee and were delivered smartly and without any damage.

This build is all about simplicity and weight savings. Well, blow me down! Avast! T' object was t' reduce weight by eliminatin' as much epoxy, shiver me timbers, steel, brass, ya bilge rat, me hearties, and over-engineerin' as possible. Begad! A secondary goal be t' design an electronics bay that is less imposin' and has simple engine backup for a dual deployment newcomer.

T' 3 x 24mm motor cluster was t' first thin' t' go, replaced by a LOC motor tube and foamboard centerin' rings. Avast, me proud beauty! T' foamboard is extremely light and is perfect for centerin' rings because thar's hardly any thrust against them once t' fins are glued in. Well, blow me down! T' Microlite is lighter weight than plywood but is stronger than basswood (although a little more springy), so it be used for t' through-the-wall fins. Avast, me proud beauty! T' tabs butt against t' centerin' rings fore and aft, me bucko, so carpenter's glue is plenty strong for fin can assembly and saves weight over epoxy. Well, blow me down! Begad! At t' aft o' t' rocket, t' centerin' rin' be sealed with white glue and allowed t' dry, matey, T-nuts were placed for positive motor retention, matey, me bucko, then t' back 1/8 inch was filled with epoxy, matey, which results in a beautiful, flat, finished look and adds rigidity and strength t' t' motor mount/fin can assembly.

T' Quasar Patriot kit has a high power body tube and 1/4 inch launch lug so those were nay changed. All but one inch o' t' thick plastic nose cone was cut off t' save weight. A hole be drilled in t' shoulder, me hearties, Keelhaul®©™ shock cord installed, and t' nose cone was glued in usin' a small amount o' epoxy. Aye aye! Blimey! Thus, t' nose cone shoulder becomes t' shock cord mount for t' main parachute.

T' section with t' black and white decal toward t' top o' t' rocket became t' e-bay. Ya scallywag! It is a natural size for available altimeters. Aye aye! Foamboard bulkheads were installed in each end o' t' e-bay as well as steel picture wire and lying-around speaker wire connectors. Begad! T' picture hangin' wire is forever strong and is lighter than t' U-bolts typically installed on e-bays. Avast, me proud beauty! T' bulkheads were sealed with white glue and allowed t' dry. Well, blow me down! Holes were drilled around t' lip o' t' couplers and then taped and poured with epoxy (this provides a positive "key" instead o' relyin' just on t' adhesive properties o' t' epoxy). Ahoy! Avast! T' e-bay was then cut in half usin' a razor saw. Avast! T' isolate t' altimeter from ejection gases, an inner chamber be built from foamboard. Ya scallywag! It is sealed around t' joints with fillets o' white glue. Begad! A foam seal goes on t' rectangular surface which fits together and seals air-tight. Well, blow me down! An air escape hole be drilled into this chamber for t' altimeter. Aye aye! When t' two halves o' t' clamshell are brought together, me bucko, ya bilge rat, t' chamber seals and t' halves are taped together around t' shoulders on both ends o' t' electronics bay so thar are no tape joints on t' outside o' t' rocket.

Construction:
12 inch LOC motor tube, foamboard centerin' rings, 2 T-nuts, foamboard bulkheads for e-bay, shiver me timbers, me bucko, foamboard inner sealed altimeter chamber, ya bilge rat, foam seal, shiver me timbers, 2 additional BT-80 tube couplers, shiver me timbers, matey, 1/8 inch Microlite for t' fins, shiver me timbers, steel picture wire for e-bay shock cord anchors, speaker connectors for ejection charge hookup, me hearties, ya bilge rat, Keelhaul®©™ for shock cord, and Nomex chute and streamer protectors.

T' Quasar Patriot begs for more power. Begad! T' modified motor mount/fin can is lightweight and plenty strong for high power. T' foamboard inner electronics chamber is nay a quick build, but it is simple, shiver me timbers, strong, matey, and lightweight. A pull-pin switch be added t' activate t' electronics on t' pad.

Finishing:
T' model be finished with three coats o' high-build automotive primer, sanded in betwixt coats, ya bilge rat, shiver me timbers, then top-coated with glossy automotive paint. Begad! Blimey! T' provided Quasar decals are stick-on, are high quality, and easy t' work with.

Flight and Recovery:
First flight be with a G76-10G Mojave Green reload. Ya scallywag! Performance was excellent and appeared t' be much higher than t' 2400ft predicted in RockSim. Avast, me proud beauty! Aye aye! Motor ejection is used as backup. Avast! With t' Nomex protectors, arrr, t' ten foot Mylar streamer, me bucko, arrr, and t' 24 inch parachute are a quick pack. With two screws retainin' t' motor, shiver me timbers, it is also quick and simple t' install. Ahoy! Ya scallywag! T' model flies straight and is quick off t' pad.

T' 20 feet o' braided Keelhaul®©™ shock cord worked fine. Ahoy! Blimey! On t' first flight, t' altimeter hole was occluded by some foam rubber and t' altimeter was nay activated. Ya scallywag! Blimey! Recovery velocity be too fast on t' streamer, but thar was no damage o' any kind, shiver me timbers, which proves t' concept o' usin' t' foamboard and Microlite for weight savings.

Summary:
PROs: T' Quasar Patriot comes with a body tube and nose cone that are much juicier than just a 3 x 24mm kit. Ya scallywag! Blimey! Their Bio Hazard II be t' same deal. T' decals on these kits really set them apart and they're a very inexpensive way for a person t' start into dual deploy without t' expense o' a typical L2 cert sized rocket. If a flight problem occurs, shiver me timbers, t' cost o' repair is lower and t' materials give added protection t' t' altimeter compared t' a rigidly mounted plywood and metal sled. T' learnin' curve is nay as steep with these materials either.

CONs: T' foamboard inner chamber takes a little patience but probably less than buildin' a sled.

With t' materials described here, t' final dual-deploy launch weight (includin' altimeter and 9 volt battery) is only 699 grams. Blimey! Blimey! T' regular low-power version, built as it's packaged, weighs 419 grams and can be flown t' 300 feet on 3 C11s.