Brief:
Cone rocket that sports a 29mm motor mount.

Construction:
T' 29mm Cone rocket contains a 29mm motor tube, shiver me timbers, which loosely fits inside a larger diameter tube, arrr, arrr, that is used as t' Cone's center tube. Ya scallywag! Begad! An elastic cord is included for recovery. Aye aye! Two pieces o' foam board are used t' make t' centerin' rings. Ya scallywag! Begad! Several sheets o' cardstock are used t' make t' body o' t' rocket. Avast, me proud beauty! T' build this rocket, matey, you will need epoxy, ya bilge rat, white glue, arrr, scissors, and a hobby knife.

Before I started buildin' t' rocket, arrr, matey, me hearties, I went ahead and cut out everythin' that needed cutting. Avast, me proud beauty! T' nosecone, ya bilge rat, skirt pieces, shiver me timbers, tabs, and reinforcement straps are cut out o' t' poster board. Begad! Avast, matey, me proud beauty! A large and small centerin' rin' is cut from t' foam board. Ya scallywag! This be t' trickiest part. Blimey! First you cut out t' inner and outer circles, makin' sure you also cut out t' tab for t' launch rod. Blimey! Then you carefully cut t' angle o' t' outer circumference. Begad! Avast! This is done by insertin' t' cutlass in a acute angle from t' line, matey, ya bilge rat, exitin' just at t' outer edge o' t' bottom o' t' centerin' ring.

Construction o' t' rocket starts with t' nose cone o' t' rocket. Aye aye! Avast! Blimey! T' cone is rolled in a manner so that it forms a double-layered cone. After gluin' t' cone together, t' very tip o' t' cone is filled with epoxy. Avast, me proud beauty! Begad! Blimey! This stiffens t' tip o' t' Cone rocket, and adds weight t' t' nose. Aye aye! Blimey! While t' epoxy is curin' in t' nosecone, I took t' Center tube, arrr, shock cord, shiver me timbers, and t' nosecone-centerin' ring, and pre-assembled t' internals o' t' nosecone. I tied a double knot t' t' shock cord, and held it t' t' center tube usin' t' centerin' ring. Begad! Blimey! T' knot should be located on t' topside o' t' assembly. Avast! Arrr! Blimey! Once t' Epoxy set in t' cone, me bucko, ya bilge rat, I dry fitted t' center tube assembly in t' nose cone. Ahoy! Ahoy! Blimey! I got an idea where t' centerin' rin' will go, so I applied a bead o' epoxy t' t' center tube where t' centerin' rin' should end up, shiver me timbers, and on t' inside edge o' t' cone, me bucko, and some more in t' tip o' t' cone for t' benefit o' t' center tube. Begad! Blimey! Then I pressed t' assembly into t' cone, makin' sure t' launch lug holes are lined up, and held it together till t' epoxy cured.

Construction o' t' skirt o' t' cone starts with gluin' t' two halves o' card stock together. Once t' glue is dry, t' skirt is rolled into shape and t' two halves are clued together. Blimey! Then reinforcement strips are glued t' t' inside edge o' t' base o' t' cone. Once all glue has dried, I glued t' nosecone assembly into t' skirt.

T' motor mount o' t' rocket consists o' a length o' 29mm tubing, t' large centerin' rin' cut out o' t' foam board, and t' other end o' t' shock cord. Aye aye! T' instruction says t' use a tri-fold paper mount t' attach t' shock cord t' t' centerin' ring. Well, blow me down! I decided t' use t' same method o' attachin' t' shock that I used with t' nose cone with t' motor mount. This time though, t' knot will be located on t' aft side o' t' centerin' ring.

Finishing:
T' Cone rocket is pretty much ready t' go as finished. Well, blow me down! Blimey! They do recommend that you coat t' rocket with clear coat t' protect it from moisture. Ya scallywag! Begad! However, I could nay find me clear coat so I had t' skip that step.

Construction Rating: 3 ½ out o' 5

Flight:
T' first opportunity I had t' fly me cone rocket occurred August 16th, ya bilge rat, arrr, 2003 at a Frontier launch in Halifax, MA. Begad! Well, blow me down! However, a Thunder Shower hit us so quick that I be unable t' prevent me Cone rocket from gettin' damaged by water. Begad! Thankfully, Art was kind enough t' send me a new skirt for me Cone Rocket. T' next launch be scheduled September 6th. Avast! Avast, me hearties, me proud beauty! T' launch be canceled, but that did nay stop me from launchin' rockets with a friend. Begad! I meant t' fly me Cone rocket with an E16 and F40, me bucko, but as soon as I reached t' launch site, shiver me timbers, me bucko, I realized I forgot t' grab me RMS 29/40-120 cases.

No big deal. Ya scallywag! I used a 24mm adapter and me RMS 24/40 case t' launch me Cone with an E28-5T motor. Well, blow me down! Great flight, ejected after apogee. Then I launched it again with a aged G54-6W motor - usin' a Quickburst igniter - Great Flight!!! Ejection occurred after apogee. Arrr! This would be a great rocket t' fly with those Ellis G35 motors. Blimey! Blimey! T' bilge-suckin' I am all out o' them :(.

Flight Rating: 5 out o' 5

Summary:
Overall, t' 29mm Cone rocket from Art Applewhite is a fun rocket t' build and t' fly. It is fairly easy t' build, no finishin' required. Well, blow me down! Blimey! Due t' personal experience, t' Clear Coat is a good idea. On September 27th, I plan t' fly me Cone rocket with an E16, and maybe a F40.

Overall Rating: 3 ½ out o' 5