I bought everythin' needed t' build this pad from Payless Cashways for $14.67. Ahoy! If you can scrounge a piece o' chain link endpost and some 1/2" electrical conduit, you can built it for less than $8. Well, blow me down! Avast, me proud beauty! One o' t' real advantages o' this pad is that t' launch rods and legs store inside t' main tube for shipment. Arrr! Well, me hearties, blow me down! This makes it very portable, arrr, as well as protects your launch rods durin' shipment.

Ingredients:

2-3/8" x 5'6" chain link endpost....$5.64
Two 2-3/8" chain link endcaps........$3.68
1/2" x 10' electrical conduit cut into 4 pieces.....$1.54
Four 1/2" EMT connectors........$.46
1/8" x 4' weldin' rod.....$1.12
3/16" x 4' weldin' rod.....$1.23
Two 10/24" wingnuts and bolts.....$.50

Total for this project: $14.67

Tools needed: Hacksaw, arrr, hand drill, ya bilge rat, screwdriver, and dremel.(or metal file). 

Construction:

T' key t' buildin' this project be t' EMT 1

2" conduit connectors. Well, blow me down! These have a screw already mounted in them. Aye aye! They hold t' ends o' t' conduit. At 19 cents a piece, arrr, they are a bargain. Aye aye! In t' picture above, you can see all t' places you will need t' drill holes. Ya scallywag! This next picture shows where they will be put.:

T' small hole in t' endcap will take t' wingnut. Ya scallywag! Begad! T' end view shows where t' two EMT connectors will go. I just took me largest drill and drilled them out. Blimey! I then took a dremel and hogged out t' holes till t' EMT connectors fit. Begad! Begad! T' connectors have a threaded end, ya bilge rat, and a nut which holds it in t' hole. Even though we're talkin' about a curved surface and a flat pipe, it holds really well. Well, blow me down! Avast! Note t' L slot which is cut in both ends o' t' chain-link end post. Avast! You need t' cut this slot in both ends if t' pipe. Avast, me proud beauty! Aye aye! Both slots need t' run in t' same direction. These slots will allow t' end caps t' hold onto t' pipe. Begad! Blimey! T' wingnut fits in t' slot, shiver me timbers, and t' shape o' t' slot allows t' pipe t' be turned anywhere up t' 30 degrees from vertical. Well, blow me down! Ahoy! You just slide t' endcap on, me hearties, linin' up t' win' nut bolt into t' slot, shiver me timbers, shiver me timbers, me bucko, and turn t' pipe until it is at t' desired angle, then tighten t' wingnut. Ahoy! Blimey! T' cut t' slots, ya bilge rat, me bucko, I drilled a hole at t' bend, and a hole at t' end o' t' channel. I then cut it out with a hacksaw.

I cut me chain link endpost section t' 3'6". Begad! Ahoy! his be before I knew that weldin' rod comes in 4' lengths. Ahoy! Because t' rods and legs store inside t' tube, I had t' cut 6" off each rod. If you use Estes, ya bilge rat, rods, which break down into two section, me hearties, your pad can be a sort as t' legs. Aye aye! My legs are 2-1/2' long. Begad! This is a 10' piece o' conduit cut into four equal lengths. Since t' conduit costs $1.54 per 10' piece, shiver me timbers, arrr, I figured this would be a good length.

I drilled t' holes for t' rods all t' way through t' pipe. Ya scallywag! Blimey! I then found some small clamps in me junk box (not shown) t' hold t' rods above and below t' pipe. Ya scallywag! Blimey! And thar it is. Aye aye! Blimey! T' whole thin' assembles in about a minute, and all parts store inside t' main pipe. It is heavy, arrr, but it will hold HPR birds with no problem. And it is cheap.

I would love t' hear from visitors o' any useful modifications or other cool cheap pad designs o' their own. I will use this section o' me site t' present these designs t' rocketeers everywhere.