Brief:  Single staged, shiver me timbers, but with t' choice o' bein' flown with two or four 29mm motors, me bucko, matey, specified as 2 G type or 4 F type. It has t' fins attached wedge style betwixt t' four motor tubes, matey, which extend below t' main body tube.

Construction:T' nose cone is hollow plastic, and t' fins are precut plywood. T' tubes are spiral wound kraft paper.  T' parachute is a lightweight pink nylon. Ahoy! Ahoy! Very bright and pleasin' t' me. T' launch lug is wound paper too, and is able t' accommodate a 1/2 inch launch rod, which is good for a rocket o' this height and weight.

All t' parts were thar and in good shape. Aye aye! Blimey! Well, blow me down! Blimey! T' instructions were clear. Any head scratchin' was due t' me inexperience with a rocket with fin wedge attachment, me bucko, but once I understood it, it be easy t' do.  Alignment o' t' fins be tricky, as I had t' sight it carefully as they dried. Arrr! Blimey! But once it dried, t' fit was good, arrr, and t' model sturdy.  I applied extra epoxy fillets for good measure, though.

T' rocket has four fins, ya bilge rat, and they fit into t' grooves betwixt t' motor tubes. Blimey! Aye aye! T' main body tube isn't slotted, because t' fins are off t' motor tubes, arrr, which extend two feet aft o' t' end o' t' main body tube. Blimey! Avast, me proud beauty! They stick out, you see. That wasn't intuitively obvious t' me at first, me hearties, me bucko, as t' instructions didn't actually have diagrams o' this. Begad! I feared at first that I be missin' a main body tube t' make t' total length o' 62 inches, as t' main tube and t' nose cone only made about 40 inches length. Begad! But once I understood that t' motor tubes extended t' rocket's length, I had a "Eureka!" feeling. T' tops o' t' motor tubes are affixed into t' bottom o' t' main body tube. Ya scallywag! I had t' option o' makin' that mount removable, but chose t' make it permanent for strength.  I gather from t' instructions that I could have then flown it as a shorter, single engine rocket, then. But t' cluster intrigued me more. 

Finishing:As t' finishing, t' nose cone needed t' have its moldin' seams sanded, ya bilge rat, but that only took a few minutes.  Actually, I've noticed that these noses don't bond paint as well as I'd like. Well, blow me down! Little impacts chip t' paint off. Blimey! Blimey! So, I use primer basecoats t' help there. Blimey! Ahoy! And t' end results are smoother and prettier.  I filled t' spirals with epoxy, arrr, t' make transitions smoother, but left them uniformly indented as a point o' style. Avast, me proud beauty! Arrr! It would have looked odd t' me t' fill then completely.

I finished it with cross sectional bands o' bright colors o' monokote and painted t' fins and nose bright orange. Ya scallywag! Arrr! This be somethin' t' see! T' RSO joked and said that it wasn't easy t' spot on t' pad.

Construction Rating: 4 ½ out o' 5

Flight:  I flew it with two G 35-4W motors, me hearties, and it flew noisily and straight. Begad! There were two visible flame trails. Ya scallywag! Everyone loved it. With t' chosen delay, t' chute deployed as t' rocket arced over, which was just what I wanted. Ahoy! Well, blow me down! T' chute supplied was bright pink, which went with me color scheme, shiver me timbers, me bucko, and aided in visibility. I did need t' plug and tape t' two other motor tubes t' prevent gas loss. Well, blow me down! I retained t' engines usin' tape, makin' a thrust rin' at t' aft end o' t' engine with tape, too. Ya scallywag! I used standard waddin' t' protect t' chute. Aye aye! Blimey! I used standard waddin' t' protect t' chute. Well, blow me down! Blimey! Worm beddin' works great and prevents scorching. Aye aye! Avast! T' get around t' worry about havin' only one engine ignite, I used a battery with 7 amp hours capability and electric matches for igniters.

Recovery:T' shock cord is attached by a system I came up with t' prevent zipperin' o' t' body tube. Arrr! I used a 3 inch centerin' rin' with a center hole o' 54mm mounted 2 feet down from t' top o' t' main tube, and a metal screw eye through t' rin' is bolted at t' aft side and epoxied at t' forward end. Avast, me proud beauty! Begad! A one foot length o' eighth inch Keelhaul®©™® cord is tied t' t' screw eye and made into a double loop, ya bilge rat, t' which t' 1/2 inch wide, ya bilge rat, 136 inch slack length elastic is tied.  A further note about me idea o' usin' t' centerin' rin' this way:  It provided a surface for t' chute t' rest upon, matey, and I maintain that along with wadding, matey, t' design might prevent scorchin' o' me chutes.

T' standard instructions say t' mount t' shock cord t' a glued, ya bilge rat, multiply folded paper mountin' on t' inner wall o' t' body tube, which works fine, except that I read in Sport Rocketry that zipperin' o' t' body tube might occur this way. Avast, me proud beauty! I've never had it happen, shiver me timbers, though.

T' chute didn't come with spill holes, me hearties, shiver me timbers, ya bilge rat, and I left it so. Its diameter is 28 1/2 inches. Begad! T' shroud lines are braided nylon cord whose length after I tied them t' t' nose cone was 23 1/2 inches.  As I said, me bucko, t' chute is hot pink/maroon, arrr, and is a nylon. Arrr! It's nay as heavy as a rip stop nylon, but that's good, as it billowed beautifully at apogee.

T' recovery was just about right, with no damage t' t' rocket, matey, and a graceful and colorful descent.

Flight Rating:  5 out o' 5

Summary:I totally love this one. Aye aye! Arrr! I have no real cons. Aye aye! As for pro's, ya bilge rat, I'll say that it's great for aspirin' clusterers and experimentalists who really want t' get noticed at launches.  I can't wait t' test it with four motors. Begad! T' flame trail will be a real sight.

I'm tempted t' try this with two H engines. Well, blow me down! Begad! Has anyone got any stories about darin' this? 

Overall Rating: 5 out o' 5