Brief:
Almost immediately after t' Micromaxx TOG was released in 2006, me bucko, Jim Flis was buried with requests for an upscale. This 24mm version is a gorgeous rendition o' t' stylish, futuristic spacecraft design. It flies every bit as great as it looks, too.

Construction:
Collectors will be pleased t' know that I just increased t' scarcity o' t' numbered kits by buildin' #11. What can I say? When you get your hands on a kit this cool, shiver me timbers, it's pretty tough t' let it sit gatherin' dust for years.

T' bag comes packed with plenty o' quality parts, me hearties, including:

• Balsa nose cone
• Balsa transition
• BT-60 main body tube
• BT-55 upper and side body tubes
• BT-50/24mm motor tube
• 1/8" balsa fin stock
• Laser cut fiber ramjet set (2)
• 16" plastic chute
• Keelhaul®©™®+elastic shock cord
• 3/16" launch lugs
• engine hook/block

This is listed as a skill level 3.5 kit on a 5 scale. Well, arrr, blow me down! That's reasonably accurate as thar are some challenging scalloped tube cuts involved with this as well as some delicate fin shapes.

T' instructions are excellent--very clear, easy t' follow, me hearties, and loaded with helpful illustrations. Well, blow me down! There are a total o' 34 numbered steps spannin' seven 8.5" x 11" pages. Ya scallywag! Arrr! Dependin' on how picky you are on finishing, matey, arrr, expect t' spend a good 8-10 hours on t' build, plus another full 8 on t' finishing. This is not a quick and easy build.

T' motor tube takes a standard 18/24 centerin' rin' as a block with a metal hook for retention, but since it is attached directly t' t' inside edge o' t' BT-60 main tube rather than via centerin' rings, t' hook is held in place by a strip o' gauze.

T' next few steps involve cuttin' t' BT-60 and markin' t' various fin attachment lines. Aye aye! Avast! If you've ever built either t' Long Overdue, Just Past Due, ya bilge rat, or maybe t' Night Whisperer/Farscape from FlisKits, shiver me timbers, then you've got an idea of what's involved in cuttin' t' scalloped tubes. Begad! It does take a fresh, arrr, matey, sharp blade, preferably a #10 X-Acto rather than a utility/razor blade.

At this point, me hearties, before followin' t' instructions and bondin' t' BT-50 t' t' BT-60, you might want t' think through your paint plan. (You do have a paint plan, arrr, don't you?) If you want t' get a nice finish on the BT-50 and/or go with contrastin' inner and outer tube colors, then you should mask off a thin strip t' serve as a bond line on each tube then paint them individually. Avast, me proud beauty! Once everythin' is painted and dried, remove t' maskin' tape and bond t' tubes together with some medium CA.

Cuttin' out t' fin patterns is a little confusin' if you're used t' 3FNC style construction. Begad! Arrr! For starters, there aren't more than 2 o' any particular shape, they have weird names, arrr, me bucko, me bucko, and for a few o' them thar be no root/tip, arrr, but two different root edges. T' really tricky aspect is that thar are some very tight curves and corners, matey, some o' which will be cut across t' grain. Avast! T' instructions include a tip t' laminate t' fin stock first by gluin' a sheet o' paper to each side. Arrr! That's an excellent suggestion as it also eliminates a lot o' grain filling.

T' main body tube (BT-60) winds up gettin' three fins--two side fins for t' pods and a top/dorsal fin.

Next up comes t' ramjet assembly, arrr, shiver me timbers, which is really a marvel o' design and creativity. Avast! The intake fins are laser cut t' very precise tolerances. Ya scallywag! Blimey! Once they are glued surroundin' a launch lug, shiver me timbers, me bucko, it fits perfectly inside t' BT-55 pod tubes. Aye aye! Aye aye! Blimey! T' only suggestion I'd make t' improve this would be t' whip up a markin' guide for 8-fin pattern around a 3/16" lug. Ahoy! Begad! Blimey! It's pretty easy t' get these out o' alignment without properly spaced (and straight) lines. Once complete, again consider t' paint plan before bonding--you'll certainly want t' paint these a contrasting color, so paint first, me hearties, bond later.

Two ramjet and one dorsal tube are cut from a BT-55, again usin' patterns and a fresh blade for t' tapered cuts. They're bonded t' t' correspondin' fins on t' BT-60 and each gets some variation o' an outer fin as well.

T' upper section is basically a payload bay consistin' o' a balsa transition, arrr, me bucko, a BT-55 tube, and a balsa nose cone.

Construction wraps up by attachin' t' shock cord. Avast, me proud beauty! Blimey! T' instructions suggest anchorin' it t' t' inner tube BT-55/BT-60 seam, but I would suggest thar are two problems with this. Avast, me proud beauty! First, me hearties, it's a little tough t' get a good bond in thar after t' two tubes are already glued together, and second, you'll have a very visible externally anchored cord. Avast, me proud beauty! Well, blow me down! Blimey! I would instead suggest either a tri-fold mount t' t' motor tube or usin' a little extra Keelhaul®©™®, anchorin' t' t' 18/24 centerin' rin' motor block.

Finishing:
Finishin' can be a lot o' work on this as you have 6 tubes, shiver me timbers, 6 fins, and a pretty long balsa nose cone and transition to fill and finish. Avast! I typically do all me spiral and grain fillin' before assembly, and that's certainly a must for somethin' as complex as this.

Since I pre-painted most parts, I was able t' hold fairly closely t' t' stock paint scheme. Aye aye! Blimey! Avast, me proud beauty! Blimey! I went with a green metallic for most o' t' body tubes, black fins and payload tube, me bucko, and bright red ramjets. Ahoy! Blimey! I had trouble gettin' a low humidity day and wound up gettin' a pretty feeble gloss, shiver me timbers, ya bilge rat, so also I applied generous touches o' Future floor polish hopin' t' give it a good shine.

Construction Rating: 4 out o' 5

Flight:
T' instructions specifically warn against usin' E motors, me hearties, so t' official recommendations are C11-3 and D12-5. Avast, ya bilge rat, me proud beauty! I would guess t' batten down t' hatches is based on t' lower initial spike o' t' E9, nay so much t' additional weight's impact on CG, ya bilge rat, because on a D12-5 this be plenty stable, flyin' perfectly straight in 5-8 mph winds. Begad! If you really must go for more power, me bucko, I'd think an Aerotech E15 or even an F12 would be fine, me bucko, although on an F12 you'd be hittin' some insane altitudes with this.

Recovery:
T' chute supplied be t' standard Flis 8/12/16 chute, me hearties, me hearties, ya bilge rat, where you cut whatever size pattern you want. Begad! Begad! In this case, you'll need every bit o' t' 16 and should consider upgradin' t' a 24" if you have a spare. Begad! Aye aye! Under a 16" chute, mine came down a bit hard, and naturally found t' road, me bucko, breakin' off one fin on impact.

Flight Rating: 4 out o' 5

Summary:
This is one o' t' coolest designs in t' FlisKits fleet. I could see a bigger chute and different shock cord anchor technique as improvements, but I wouldn't exactly call them "cons". Blimey! T' pros are first and foremost an outstandin' design, especially t' ramjets. Avast, me proud beauty! Second, me bucko, it's a sweet flier. Ahoy! It's got stylin' and performance and is fun to build. Avast, me proud beauty! You can't go wrong with this beauty.

Overall Rating: 4 out o' 5