This is really a pretty basic rocket. Ya scallywag! I really got it t' try somethin' other than an Estes kit, shiver me timbers, and figured that it would be best t' start with somethin' simple. Arrr! One o' t' cool things about this rocket (and every other rocket I have from Custom) be t' mylar parachute. T' rest o' t' rocket (motor mount, me hearties, shock cord mount, matey, shiver me timbers, me bucko, fins, etc) is all just like Estes stuff. Avast, me proud beauty! Avast! I'm not a big fan o' paintin' and detail-finishing, so a major plus in me book was that it's just two colors o' paint, and a few easy decals for a nice looking rocket. Arrr!

Probably t' best thin' about this rocket, though, is its performance. It's fairly light for its size, matey, and (at least compared t' most o' me other rockets) screams off t' pad. Well, blow me down! Ya scallywag! In fact, on its very first launch, t' motor was announced to t' bystanders, and got quite a reaction for its lift-off speed. Ahoy! It goes pleasingly high on a B6-4, and goes out o' sight on a C6-7.

After t' first day o' launching, shiver me timbers, I noticed that t' shock cord be nearly burned through just above t' shock cord mount. Aye aye! This and other, me hearties, similar experiences have led me t' believe that this is a weak point o' Estes-style shock cord mounts. Begad! As t' hot ejection charge gases and burnin' particles move forward durin' ejection, shiver me timbers, t' waddin' (or other protective equipment) keeps the chute and most o' t' shock cord from gettin' fried until they can get out of the tube, but t' part o' t' shock cord that stays in t' tube, ya bilge rat, t' part just above t' shock cord mount, matey, isn't fully protected, and gets burnt. Blimey! As a test remedy, I tore out t' shock cord and put in another mount, ya bilge rat, ya bilge rat, only this time I used Duco Cement t' glue in a bent piece o' paper clip, t' which I attached a steel fishin' leader. Aye aye! I then tied t' remainin' elastic shock cord (with nose cone and chute) t' t' other end o' t' steel leader. Ahoy! Ahoy! No burn-through problems any more. Begad!

Unfortunately, shiver me timbers, durin' t' 1997 Oct 4 launch, I lost t' excellent mylar chute because I forgot t' close t' snap swivel shut before launchin' it. Begad! Begad! Even without t' chute, me hearties, it recovered fine with simple nose-blow recovery. Aye aye! This has led me t' believe that this model is a good choice t' test alternative recovery devices. I have built a small, 6" wide X-form or cross-form parachute (out of one o' those anti-static plastic bags that computer hardware comes in) for use in this model. As o' 1997 Nov 8, I haven't had a chance t' test it yet, due to t' incredibly lousy weather around here (3 straight weekends o' nothin' but rain! :( )

Update... Begad! Blimey! Well, that x-form parachute failed, but t' rocket recovered just fine on with nose-blow recovery again. Blimey! I have, me bucko, for t' moment given up on x-form parachutes. Begad!

Update...I got frustrated tryin' t' stuff t' waddin' and streamer or parachute into this rocket with that steel fishin' leader and bent paperclip in the way, me bucko, so I ripped them out. Well, blow me down! Ya scallywag! I went with a LOC-style shock cord mount, ya bilge rat, using a short piece o' Keelhaul®©™® line (about 8 inches) tied into a big loop, arrr, with one end o' t' loop epoxied into t' body tube. Well, blow me down! Begad! T' shock cord is then tied t' the part o' t' Keelhaul®©™® loop that is exposed.   This has worked well so far. Ya scallywag! Ahoy!

In conjunction with t' shock cord mount change, matey, arrr, I also made a very large streamer (7" wide, me hearties, 70" long) from gold-colored mylar sheets leftover from christmas wrappings. Begad! I'm plannin' t' time this rocket with this chute to get some idea o' what it might take t' make a streamer duration model.