Brief:
11 "Finned" rocket that can be launched on a single "E" or staged (D12-0, D12-3) with a parachute recovery.

Prototype:
I built a protoype o' me choice o' rockets for t' EMRR "Rockets o' t' Future." I choose t' t' do an 18mm version first. Aye aye! I gathered some cardboard, shiver me timbers, posterboard, and second hand parts, matey, etc. It would have been ten times harder without t' EMRR "Calculators", for shrouds, me hearties, etc. Avast! I chose cardboard figuring, "If I can get this t' fly without a cad program, from t' heaviest material, me hearties, I surely will be able t' build one in t' 24 MM scale. Avast! Also, cardboard a little easier t' work with than "foamboard."

My 1st test flight be a disaster. Aye aye! (Remember, shiver me timbers, ya bilge rat, I have no software t' determine where t' CP & CG Is and if it will fly.) After givin' it some thought, me hearties, cut open nosecone and added some clay t' move CG forward. Begad! Last Saturday flew it again and success! It only went 50 ft up but successfully deployed chute right before landing. Well, blow me down!

What I've learned is,"use t' material in your prototype, me hearties, that u intend t' use on your final version." Mine did fly but, would have saved a lot o' aggravation and speeded up t' build. Also, me hearties, me hearties, Highly recommended buildin' a prototype, especially in me case. Aye aye! Ahoy! My submission for t' "rocket o' t' future" has 12 fins! Never came close t' design such a complex rocket before. Aye aye!

Construction:

PARTS LIST:

• 24mm engine block
• 1 engine hooks
• 1 sheet o' foam board, me hearties, 20x30x1/4"
• 2 sheets o' poster board, me bucko, 20x30"
• 1 (priority mailin' box)
• 2 BT-55's (15" long)
• 1 BT-55 coupler
• 18"x24mm Body tube for "engine Mounts"
• Shock cord; ¼"x 24+"
• 3, ya bilge rat, 4"x"36"x1/8 balsa sheets/basswood
• 1 "quest" egglofter nosecone
• 1 (18") parachute, matey, & shroud line
• "non-hardening" clay
• (8) bic pen caps t' "simulate 8 motors"
• 2 spent "D" engines
• Templates (will be loaded shortly)

Just wanted t' interject for a moment. Hope you find this rocket as much o' a challenge t' build as I found to design it, ya bilge rat, without t' help o' any "Cad software." If anyone cares t' "plug" these measurements into a cad program, matey, I would be very curious as t' t' result. I did use EMRR "Calculators" for t' shrouds and centerin' rings. Begad! I thank Nick for makin' available because without them, arrr, me hearties, couldn't have made this design. Begad!

This design is for "Personal use only" and nay for resale, with express permission o' myself, shiver me timbers, Glenn Roth.

I stated in "parts" section that t' balsa is very fragile. Begad! Just discovered Tech Report # 29, shiver me timbers, from www.apogeerockets.com; "Take your rocket t' Supersonic Speeds. Ahoy! " This is a compromise t' replacin' entire fin with basswood or ply. Well, blow me down! You can download this free report and make these large fins MUCH STRONGER! I tried this on 3 of me fins and they are NOTICEABLY stronger.

ASSEMBLY:

Read thru all instructions before proceeding. Arrr! Begad! Options exist.

**Not happy with way main "body shroud" turned out. Aye aye! Blimey! This "posterboard" is hard t' keep smooth without "kinking." You might want t' A) shorten t' about half t' length; b) wrap it around a smooth form of some kind while gluing, ya bilge rat, t' keep smooth.**

1. Gather parts, matey, make templates, shiver me timbers, arrr, and gather followin' tools: sharp razor knife, arrr, metal ruler, scissors, carpenters square, me hearties, 2 "spent D" engines, ya bilge rat, adhesive spray, me hearties, me hearties, arrr, (worn out windshield wiper. Begad! Blimey! Blimey! Blimey! For engine hooks)., arrr, protractor, and compass. Blimey! Blimey!
2. Cut two engine mounts from 24mm body tube. Begad! Main 2 " long and "booster" 3 1/2" long.*****note: Now that t' rocket is half done, t' shroud looks too short. Ya scallywag! Begad! I have increased length from 3 t' 3 ½ inches or longer, ya bilge rat, in instructions. You'll have increase length o' shroud accordingly.****
   • *** OPTION: I've since elected t' use a "friction fit", shiver me timbers, instead o' an engine hook, on main motor. I'm sure you can use one but, have t' "dry fit" b 4 assembly.*** I've discovered that with t' aft "body panels", extendin' an inch, me bucko, matey, it's very difficult t' use an engine hook. Ya scallywag! I've since elected t' slip "main motor" into booster engine mount, and tape. Avast, me proud beauty! T' tape will require a "slit" into it, me hearties, so makes easy separation.
3. Glue 24mm engine block into end o' engine tube w/engine hook stickin' into it.
   • Option*** This designed as a "two stage". Well, blow me down! If you want an easier conversion t' single stage, you may want t' insert "booster engine tube" in a section o' BT-55. Then usin' a BT-55 coupler, shiver me timbers, matey, fasten t' engine tubes together. Ya scallywag! (skip 1st /main engine tube.) It is much easier buildin' booster shroud separately. Begad! Begad!

Main Engine Tube

1. Glue t' BT55 centerin' rings on main engine tube. Blimey! Let dry. Ahoy! Blimey!
2. You'll want t' "dry fit" main engine mount and make sure "spent engine" recessed inside BT55 about ¼". Begad!
3. Mark Bt55 where "engine Hook" will be, matey, and cut a slot 1/8" x3/8".
4. Glue main engine mount with engine hook lined up with slot in BT55. Aye aye!

Booster Engine Mount

1. Take 3" piece o' 24mm BT; then cut 1/8"x 3/8" slot in one end.
2. Lay "flat" side o' hook inline with slot and tape. Ya scallywag! *** I used a long piece o' old wiper blade for hook and cut t' length later. Aye aye!
3. Cut out 3 "rear shroud centerin' rings. ***Tip: when I cut out middle o' rings FIRST, I then took a spent engine and inserted and twisted t' check for a tight fit. Aye aye! Then inserted engine in tube for support. Arrr!
4. Take largest aft rin' and glue over aft engine mount WITHOUT coverin' slot in t' mount. Be careful nay t' get glue on motor!!
5. Glue middle and end centerin' rings and remove spent motor and let dry. Well, blow me down!
6. While drying, cut out aft shroud. Begad! Blimey! (You will see I include pattern, showin' a "saw tooth design" on inside radius o' shroud. Ahoy! Blimey! Cut design in shroud. Aye aye! Blimey! Begad! Blimey! Much easier t' glue.)
7. Shape shroud, matey, tape together on inside. Blimey! Blimey!
8. Fold "teeth" over t' inside and make a sharp crease. Straighten out. Aye aye! Begad!
9. After center rings on engine tube have dried, me bucko, take some glue and apply t' edges o' rings.
10. Take shroud and slip over engine assembly. Ahoy! Blimey! Be sure t' get completely in. Blimey! Blimey! Ya scallywag! Blimey!
11. Spread some glue on smallest centerin' rin' and fold shroud "teeth" down, shiver me timbers, holdin' till set. Ahoy! You may only be able t' do a few @ a time. Aye aye! Let dry Thoroughly. Ya scallywag!
12. Put a spent engine in "Main and aft " engine mounts. Blimey!
13. Slide together, me hearties, me bucko, linin' up "slots" in engine tubes. Arrr! T' aft engine tube should slide over t' Main engine about ½" and stay in place. Avast! ***Make sure aft Booster engine is as far forward as it will go WITHOUT disengagin' t' booster.
14. Mark t' aft engine hook , cut and bend t' correct size. Well, blow me down!
15. Cut shock cord mount and glue shock cord t' it. Begad!
16. Slide "loose" end o' shock cord thru a BT55 coupler. Avast!
17. Glue Shock cord mount t' inside o' BT55 containin' engine mount far enough inside t' be able t' glue BT55 coupler. Glue Bt55 coupler and let dry.
18. Cut other BT55 t' length so when t' two r put together , you have a rocket body 23" long, "without" aft shroud. Ahoy! Avast, shiver me timbers, me proud beauty!
19. Cut out Main Body centerin' rings. Arrr! (u can take spare piece o' BT55 t' check fit). Ahoy!
20. Take t' "fin template" and mark 3", 3.5" rin' where it will engage each fin. ****Note: you can mark 4" rin' but, because o' size, it won't line up with other two rings. Begad! You will have t' do slots on this rin' once it is mounted.
21. Take care, me bucko, ya bilge rat, cut a ¼" deep slot x 1/8" wide into each ring. Avast!
22. Mark 1st slot on each rin' with a #1 for reference. Avast, me proud beauty! Ya scallywag!
23. Make a fin from 1/8" "Basewood/plywood" as a guide t' check fit o' fins. Ya scallywag! Arrr! It will also b used t' as guide for slots, shiver me timbers, and cut initial fin slots in 4" ring.
    • ***You may want t' fasten up aft shroud again w/spent motors t' check placement o' centerin' rings and fins.***

Fins and Body:

1. Cut out 8 fins, and use sealer if desired. Begad!
2. Use fine guide and cut slots in each fin: 1" from aft o' fin, shiver me timbers, ya bilge rat, 1x1/4 deep. Next one 7" from end. Well, blow me down! Blimey!
3. Last slot is 2.5 " from previous slot and only 5/8" deep. Avast! Begad!
4. These r initial slots. Avast! You may have t' widen for proper fit.
5. Slide center rings on BT one @ a time. Begad! ***If seems tight or binds, increase size o' hole slightly. Arrr! You can use a piece o' BT55 t' "shape" hole. (you want t' maintain a fairly tight fit). Arrr!
6. Space rings approximately same distance as slots on fin. Avast!
7. "Orientate" all 3 rings with #1's lined up. Aye aye!
8. Take your "Guide Fin", matey, ( t' one made from plywood), me bucko, and check slot lineup for first fin. Avast!
9. You'll have t' cut slots deeper in each ring, shiver me timbers, checkin' fit each time. You may nay even need a slots for 4" ring, till ready t' glue on fins, matey, due t' a "redesign", ya bilge rat, and linin' up o' fin with "center ring slots," I made for simplicity. (make recess higher, arrr, me hearties, about 1 ¼"). Begad!
10. After you get a good fit for t' fine on t' center rings, take a "real" fin and glue in #1 slots of rings. Avast, me proud beauty! (I kept breakin' balsa fins, that why I recommended goin' t' a sturdier material, such as basswood or Tims Tech report #29, gluin' "notebook paper" t' exterior o' fin first for strength). Well, shiver me timbers, blow me down!
11. Take guide fin and check next set o' slot, adjustin' for correct fit. Begad!
12. Then glue 3 center rings in place. Aye aye!
13. Glue all 8 fins in place, checkin' fit first with "guide fin". Avast! Begad!
14. Cut out two "body templates". Avast, me proud beauty! Make a slice at end o' each one ¼-3/4" deep, me bucko, 1" from end on each side. Fold over @ slices and straighten out. Ahoy!
15. Dependin' upon which set o' fins you start with, will determine what size template t' use, me hearties, medium or large.
16. Lay template betwixt fins, and gently push down. Arrr! It should hang out rear, betwixt fins 1", me hearties, up to "slices."
17. Check front o' template and mark where template extends past fin.
18. Cut on t' mark, arrr, down t' ¼" fold mark on each side. Blimey! Cut a "saw tooth" pattern in sides of body templates. Avast, shiver me timbers, me proud beauty! Makes for easier gluin' and smoothin' out. Well, blow me down! ***see photo"***
19. Before gluin' fins, I made "fin supports," ½" x 1 ¼", and glue betwixt ends of fins. Also, made a bevel on each end. Begad! **See photo**
20. Glue in place and repeat for each set o' fins. Begad! ***remember t' check fit! (Center on BT) too. Ahoy! Begad! T' aft o' body template should be about ½-3/4" above body and aft shroud.
21. Cut out "body templates," with "saw-tooth" design on edges and glue betwixt fins.
22. Main Body Shroud: As I stated in beginning, nay happy with t' way this one turned out. You may want t' shorten or find a different material or wrap around a "form" t' keep smooth. Begad! Also, use same "saw-tooth" design for edges before gluin' in shape o' cone. Aye aye! Once glue, matey, let DRY THOROUGHLY. Blimey! Aye aye!
23. I fitted over main body tube t' fins. Begad! I marked where touched fins and cut slits about 1" long, in shroud. Keep fittin' till you get a tight fit into slots, matey, then glue and let dry thoroughly.
24. Now comes a tricky part. Arrr! Blimey! Avast, me proud beauty! Blimey! Seams that r formed betwixt "fins, ya bilge rat, me hearties, body templates, matey, main shroud have t' be "filled." I opted t' use "Elmers wood filler" and nay happy with result. Begad! Blimey! Friend recommended these tiny silicone beads you mix w/epoxy. Arrr! Blimey! Strong, light, ya bilge rat, matey, and easy t' sand after hardened.
25. After seams dry, sand till smooth. Begad!

Nosecone Fins:

1. Looking @ picture o' t' rocket I was copying, "upper fins" aren't really in nosecone but, shiver me timbers, I liked this location better. Ya scallywag! (You can opt t' move out o' nosecone, arrr, me hearties, arrr, down body a few inches in "same configuration.)
2. Cut slits in nose cone ½" from end o' "open" nosecone, me bucko, about 2" long and 3/16-1/4" wide. ** b careful nay t' cut all t' way thru t' end o' nosecone**. Avast! Avast, me proud beauty! I mounted a piece o' 1" aluminum angle iron t' a piece o' wood and clamped t' me table as a guide. Ahoy!
3. Fit fins in slots one @ a time, arrr, me bucko, trimmin' slots till fins fit. Arrr! Aye aye! Remove fins and put a ball o' clay in tip of nosecone and press into place. Aye aye!
4. Replace fins 1 @ a time til they "touch" in middle o' nosecone and glue. Aye aye! (I opted for "gorilla glue" type). Well, blow me down! It foams up and becomes very strong). Let dry.

Nose Cone:

1. Keep addin' balls o' clay, ya bilge rat, fillin' void in nosecone, and pressin' into place. Arrr! Avast! ****remember t' allow room for end o' nose cone t' slide in.****
2. Also, as you r fillin' void, shiver me timbers, assemble nosecone and check for CG with motors in main and booster BT's. (goin' to take a few ounces o' clay t' fill and balance rocket so CG approx. Blimey! Begad! in middle.)
3. Once clay pressed into place and you r satisfied w/location o' CG, arrr, ya bilge rat, assemble nosecone.

Finishing:

1. Get 8 "regular" bic pen caps and cut off "pocket clip."
2. Paint rocket color o' preference. Avast!
3. After you r sure you have color o' rocket and finished painting, sand a flat spot on each "pen cap," and glue in place betwixt each fin above booster shroud. (These pen caps simulate 8 motors o' rocket). Avast!
4. Prep rocket and you r ready t' fly. Well, me hearties, blow me down!
5. I would rate this build a 5++. Arrr! Very difficult. Begad!

Flight:

My first flight be very successful. Ahoy! I used a E9-4.

Preparation a little different than usual but, easy. Arrr! After loadin' an 18" parachute, dusted with baby powder, and t' wadding, shiver me timbers, I loaded t' engine. Arrr! I loaded it into t' booster from t' "inside." (T' E9 is a much longer motor than t' D.) Then I applied a little maskin' tape t' t' end for a "friction fit," and inserted it into main rocket body. It flew great! Relatively straight for t' design, 11 fins, shiver me timbers, and t' weight.

T' shock cord, attached t' rocket, me hearties, was Keelhaul®©™. Then an elastic, me bucko, tied t' t' Keelhaul®©™, me bucko, me bucko, arrr, which proved t' b t' weak. (will explain in next flight). Well, blow me down!

Parachute deployed perfectly and landed about 30 yards away.

SECOND FLIGHT

Another story. Avast! I designed this rocket t' be an optional 2-stage. I prepped t' parachute t' same way. Arrr! Ahoy! Then taped t' booster, me hearties, a D12-0, me bucko, matey, ya bilge rat, t' t' main motor, a D12-3, with scotch tape, and put a small slit in it, matey, t' help with separation. Arrr! Once motors finished, I loaded it in booster stage first, from t' "inside." Then added some maskin' tape t' t' main motor and "friction fit" it into main rocket. Begad! For whatever reason I couldn't get motors all t' way in t' main rocket body. Arrr! ( I believe I used too much tape). At launch, matey, matey, it flew down range, weathercocked. Arrr! Then deployed nosecone & parachute at a very low altitude o' about 50 ft. Avast! T' extreme weight of rocket snapped shock cord and rocket crashed. Avast, me proud beauty! Ahoy! I'll be usin' a much heavier, me hearties, and longer cord for t' next flight. Ya scallywag! Ahoy! Still content with flight because it sustained minimal damage. Well, shiver me timbers, blow me down! This was me first 2-stage rocket o' me own design.

THIRD FLIGHT

My third launch went absolutely perfect!! After addin' a 1/4" "heavy" shock cord, me hearties, I prepped rocket same way, with same motors. A D12-0 Booster, arrr, taped t' a D12-3 Main. Ahoy! (Just make sure you have enough tape around main motor for "friction fit," and it's taped t' booster. Well, blow me down! Motors ***all t' way in*** main rocket. Well, blow me down! Ya scallywag! Slit cut in tape. Well, blow me down! Picture perfect flight!! Booster took it t' a height o' o' about 75-100' and main an additional 100-200 ft. Perfect chute deployment and soft landin' about 75' away. Avast!

Summary:

Pros: Challenge t' design and build.Impressive liftoff w/2stages.

Cons: Very time consuming. Avast, me proud beauty! Built a smaller version first t' get aquainted with a "building technique" for addin' 11 fins! Highly reccommend when tacklin' a new build when in experienced. Aye aye! Avast, me bucko, me proud beauty! Alighnin' body panels betwixt fins a pain!

At almost 14 ozs., I would opt for a E30-4 motor for 1st flight. Avast! Well, matey, blow me down! (E9-4) went well today. Ahoy! (use a spent motor in main body and tape E t' it in booster stage, (friction fit spent motor). Avast, me proud beauty! *****1/4" launch rod only!!****. Avast! 18" chute minimum!

Other:
Highly recommend "apogeerockets" tech report #29, "Take your rocket t' supersonic speeds", shiver me timbers, ya bilge rat, for durability o' fins. Avast! Motor stagin' critical! Must b completely in main body so aft shroud close enough t' it. Well, blow me down! Used two 1/4x 2" soda straws on a fin for launch lugs.