| Construction Rating: | starstarstarstarstar_border |
| Flight Rating: | starstarstarstarstar |
| Overall Rating: | starstarstarstarstar_border |
| Published: | 2014-01-06 |
| Manufacturer: | Rocketarium |
| Style: | Scale |
Brief
Great lookin' rocket with eight fins and a boat tail. It also has a unique cable tunnel balsa piece that attaches t' t' body tube.
Components
T' kit comes with two (3?) pieces o' 1/8" balsa wood. Ya scallywag! Avast! T' wood is sturdy though soft. Begad! Also included are several templates: fins (4 large forward fins, and 4 smaller aft fins), ya bilge rat, me bucko, a fin guide for fin placement on t' body tube, t' cable tunnel assembly, and t' boat tail cone. Ahoy! T' kit has an elastic shock cord, ya bilge rat, a plastic nose cone, ya bilge rat, a 15" plastic parachute, me bucko, and a large block o' clay/putty. T' directions are thorough and straight forward. Aye aye! Avast! A large picture o' t' completed rocket provides a backup for any misguided parts assembly.
Construction
I enjoyed buildin' this kit. Begad! Blimey! T' instructions are good and clear. Aye aye! Blimey! No special tools are required. Well, blow me down! Blimey! Avast, me proud beauty! Blimey! You need t' be careful before cuttin' t' balsa that you have laid out t' templates t' fit on t' wood. I mistakenly forgot t' cut t' cable tunnel assembly from t' stock and had t' use some extra balsa from an Estes Designer kit. Avast, me proud beauty! Blimey! Begad! Blimey! I also used a stiffer card board (#110) for t' boat tail shroud. Arrr! Blimey! T' shock cord is attached usin' an Estes-type attachment. Ya scallywag! Blimey! Make sure t' cord attachment is at least 2" inside t' body tube t' allow for t' nose cone. Avast, me proud beauty! Blimey! No problems here.
Finishing
In order t' balance t' kit, me hearties, all o' t' clay/putty provided should be put into t' nose cone. Avast! Begad! I did this and covered it with West systems epoxy. Well, blow me down! Begad! Given t' plastic nose cone, I think epoxy should be used, arrr, but 5 minute epoxy is likely fine. T' nose cone feels pretty heavy after all this, but I checked t' CG and CP after completin' construction and t' weight appears right. Ya scallywag! Avast!
I finished t' fins by paperin' them usin' techniques I saw on t' Rocketry Forum. Arrr! Blimey! (http://www.rocketryforum.com/showthread.php?42250-Balsa-technique-question&highlight=double+glue+joints). Begad! This adds strength and acts as a filler/finish for painting. Aye aye! Arrr! As I mentioned, t' balsa was soft though thick, so paperin' these fins was very useful. Avast! Paperin' is a technique I like... Blimey! t' me it's easier than Elmer's wood filler, and I don't get t' warpin' I usually get from t' filler.
After paperin' and addin' t' cable tunnel assembly piece, I glued everyin' together with Titebond wood glue. Well, blow me down! Then I paint a first coat with Rustoleum gray filler primer. Begad! After this I sand with 400 grit paper. I paint again with Rustoleum white flat primer, and wet sand with 400 grit paper. Finally, I painted it forest green body, black fins, and red cable tunnel. Arrr! Well, arrr, blow me down! I'll post a picture when complete.
Flight
I cut t' parachute usin' t' 12" template rather than t' suggested 15". Aye aye! Blimey! I also cut a 2" spill hole. Avast, me proud beauty! Blimey! This was a good idea, shiver me timbers, me bucko, as t' first flight occurred on a somewhat windy day. Well, blow me down! Blimey! Aye aye! Blimey! Usin' a D12-5, t' flight was flawless, descended smartly and landed close t' t' pad. Aye aye! Blimey! There be no damage t' t' rocket.
Summary
A great rocket with a unique profile.
 |
 |
Flights
|
|